User Manual () Upgrade Instructions; 07/01/15; Download; Release Notes. Datasheet (). Datasheet () Upgrade Instructions; 08/31/15; Download. Don’t forget about our other Dlink DSLB info that you might be interested in. Login to Dlink DSLB Router ยท Change your Dlink DSLB IP Address. 5) The power light will first go red and the DSL light will flash. The DSL B comes with a lot of Manual Setup tick box and click the Setup Wizard button.

Author: Vudoran Goltim
Country: Mali
Language: English (Spanish)
Genre: Business
Published (Last): 20 August 2010
Pages: 21
PDF File Size: 1.87 Mb
ePub File Size: 12.43 Mb
ISBN: 345-8-40560-806-3
Downloads: 3811
Price: Free* [*Free Regsitration Required]
Uploader: Shakarr

Click to add a DDNS service. Password Enter the password. Click the Admin button to change the routers account passwords.

D-Link Technical Support

Page 80 To configure an individual interface, select the desired RIP version and operation, followed by selecting the Enabled checkbox for manial interface. In this page, you can set the Internet time. D-Link has manuql the products you need to build your network. You can select Log Level from the drop-down list. Wan Interface Information The WAN Info page displays the status and the connect or disconnect button, depending on the selected connection mode.

Installation Gently fasten the two slots with the screws. Certificate To apply for a certificate, click on Create Certificate Request. To print the manual completely, please, download it. Enter the path of the image file location or click the Browse button to locate the image file. Then turn on and boot up your PC and any LAN devices, such as hubs or switches, and any computers connected to them. There are three buttons at the bottom of the page; Next Connection appears only if you have created more than one connectionTest and Test with OAM F4 which will allow you to retest if necessary.


A Beacon is a packet of information that is sent from a connected device to all other devices where it announces its availability and readiness. Click on the Add button to create a mapping group. Click LAN and the right page appears. Enter a MAC address of a computer manuual your network and click Dsl-260b. You can query information of packets recevied at the Ethernet, and wireless interfaces.

To print the manual completely, please, download it. Page 89 Web Configuration To create a new mapping group, click Add. Then you can enter certificate name, paste certificate content.

Download Manual for the Dlink DSLB

Mannual limits are designed to provide reasonable protection against harmful interference in a residential installation. Warranty or superior in all material respects to the defective Hardware.

After proper configuration, the right page appears. To verify your IP address, please follow the steps below. In this page, you can set the service description, enable Click Apply to save. Wireless adsl2 plus router with ethernet wan support 38 pages.

Blocked means that all MAC layer frames are blocked except those matching with any of the specified rules in the following table. Tools Click the Manjal button to change the routers account passwords. All events above or equal to the selected log level will be logged and displayed. Click Apply when finished.


Click Reset Statistics to restore the values to zero and recount them. When you are ready, click Next to continue.

D-Link DSL 2640B Setup Manual

Troubleshooting Troubleshooting This chapter provides solutions to problems that might occur during dsl-2640n installation and operation of the DSLB. If you uncheck the DSL Auto-connect box, more options will appear below the check box.

Step 3 Slowly take your hands off the device.

The Wireless — QoS section allows you to configure the wireless quality of service for the router. This tool can be helpful for security purposes if you wish to limit the transmission range.

Click Apply to apply the settings. Click on OK twice to save your changes and then close the Control Panel. Page 59 High network traffic areas should select Short preamble type.

When satisfied with the settings click the Apply button. Select the desired DSL test mode and then click the Apply button. Click Certificate, the right page appears. Select a classification queue.